• 🔖 It looks like you are browsing the site as a guest. By registering on the site you can participate on the Internet's largest Polaris Ranger XD 1500 forum. To register, simply Click Here!

Recent content by Skippy

  1. Skippy

    Aftermarket Assassins Exhaust

    I guess I need to put more effort into it , the tail pipe wouldn’t move even a little bit. I haven’t noticed mine getting hot , need check next night I have it out .
  2. Skippy

    Aftermarket Assassins Exhaust

    Has anyone checked the spark arrestor , on my RZR xp the the screen would get cover in what looked like fine fiberglass , it had to restrict the flow . I tried to remove the tailpipe and check mine on the XD but it was very tight , finely gave up without getting the screen checked
  3. Skippy

    Steering alignment

    Mine tracks really nice , the BFG KM3 tires I think have a lot to do with that . My wheel is just a little off probably 1 turn would take care of it. If I have to pull the boot to get to the nut I might forget about it…. But probably not.
  4. Skippy

    Steering alignment

    Has anyone adjusted the tie rods ? I was wondering about the inner jam nut , looks like you have to cut the band on the boot and slide it out the tie rod to get to the jam nut on the inside . I thought maybe there was only the outer jam nut .
  5. Skippy

    New here

    Welcome to the group , we really enjoy ours the year round .Someone can answer about any questions you might have . Enjoy the new ride .
  6. Skippy

    Air leaks

    I think the 2026 pieces are on the outside and the 2024 & 2025 are on the inside of the block off panel . If you compare the parts diagrams .
  7. Skippy

    2026 vs 2025 XD 1500 ultimate

    I thought about ordering the pieces , currently says all are on back order . Mine seems very good around dash area , no cold air. I get a little around drivers door handle at times . I thought it might help insulate the radiator heat on 90 degree days . All in all mine has been really good , I...
  8. Skippy

    2026 vs 2025 XD 1500 ultimate

    I think the new pieces are on the outside under the fenders and some look like plugs , maybe to fill holes some have been filling with foam . I think there are ten pieces.
  9. Skippy

    Walker Evans shocks

    My thoughts exactly , anything other than stock location should be listed somewhere . Website description would be enough , they do list for stock an arms only . Polaris now owns Walker Evans , maybe some install instructions on the web like they have for other accessories . I haven’t tried...
  10. Skippy

    Walker Evans shocks

    Jay B I got answer back from Christopher at Walker Evans , the shocks were designed for the outer position . That was the message in entirety short and sweet. The outer hole seams have close to standard ride height with the Walkers . With the inside hole on the rear’s I would have to adjust...
  11. Skippy

    Washer or No washer!

    I don’t remember one on the plug from the factory , I didn’t get one in the kit .
  12. Skippy

    Walker Evans shocks

    I sent an email this morning I hope they respond , there is more clearance on the outside hole . Most seam to think the ride is stiffer on the outside hole. , kind of defeats the purpose of the upgraded shocks. I will let you know if Walker responds , they didn’t answer my questions before...
  13. Skippy

    Walker Evans shocks

    They bolted up ok on the inner hole , but there was no room for the shock to pivot . As the suspension loaded the top of shock hits on frame mount , like the eye on the shock is to close to the shock body to allow it pivot on the top bolt . I’m going to try to get them on the phone tomorrow ...
  14. Skippy

    Walker Evans shocks

    JB Could you tell me which hole you used to mount the front shocks , the inner hole where the stock shocks were mounted the Walker shock body hits on the shock mount ,like shock eye is to close to the shock body. I’m going to try the outer hole next . The top shock mount is a pain to get at ...
  15. Skippy

    What audio modifications are you guys doing?

    Thanks Tazman I think the hardest part of this install is getting the seat back off , I tried to take one of the front seat backs off and gave up before I broke the clips off . Real pain in the ass to take the seats out .
Back
Top